Home
Shop
3D Wall Panelling Interior
3d Decorative Panels
3D Wall Panels Peel and Stick
3D Brick Sticker
3D Wallboard
Plastic 3d Wall Panel
Best 3D Wall Panels
About
I actually did not expect much but it does the job perfectly. Yes would recommend
Looks good, nice adhesive.
I thought they were nice looking. The glue seems like it is OK but it easily gets all over your hands. You will probably have to purchase an adhesive remover and be prepared to paint your wall. If you ever have to remove them. Recommend using a level when installing every row. They tend to stretch a little bit when you are installing them on the wall so you need to pay close attention to them so you dont put it on distorted. I also cut one almost in half so I could stagger every row. I saw some
Easy to install or to correct if misaligned. Looks real too. Way better than trying to wall paper a wall.
The 3D brick texture is okay. Problem is they aren't to scale of actual bricks. It makes them look obviously fake because they are so small. Wanted to do a backsplash to go with an adjacent brick wall and it' a no go. Also the seams don't match up to make a seamless pattern.
These tiles are not white. They are more of a linen white with almost a yellow tint. Picture doesn't show it very well.
Easy to cut to size with guides on back, quick installation and it made my little electric fireplace mantle look richer. I like it!
I absolutely LOVED working with these panels. They are very easy to cut and very flexible. I actually had FUN placing them on the wall. They stuck VERY well. I took one small cut off piece off to replace it with another, and it was very, very well stuck on. They look fantastic! I was amazed at how realistic they look. The panels are foam and quite bouncy - you can push your finger into it and it comes back out. I also like the color. It' like a pearl white. I was going to paint it white since
This was thinner than I expected but made it very easy to cut with sharp scissors. I put mine up in about 30 minutes, over my old fireplace surround tiles. I need to buy another pack of 10 to finish it up, but sitting on the couch it looks great! (Cant see the lower part that isnt finished yet!) I was a little hesitant about the color based on previous pictures on reviews. It seemed to pick up more browns than I was wanting in other peoples pictures, but with gray and white around it, they pi
For all the DIYer out there.. this product is very simple to use and works great! Very sticky on the back so make sure you know where its going to be placed! We are going to purchase more once I finish above the stove!
LOVE THIS! Super easy to stick to your wall. Great quality and it looks like actual brick. The material is actually soft and foam like.
Dont care for the pinkish tint in the beige but I wanted to insulate the wall without gutting. Be careful after you peel the back off that you dont let that paper fall on anything because the glue will stick. I let mine fall on the floor and when I picked it up glue was stuck to floor. Does the trick in the end.
This tile is beautiful, strong and well made. Very versatile and goes well with any color. Study carefully where you want to place your tile because once it' in place it is difficult to remove and will remove any surface in its path.
This my first time with any kind of wallpaper. After reading the reviews I almost didn't order.. I am so glad I did! The trickiest part for me was figuring out the pattern repeat, and how to start the next column so the pattern lines up. A quick tip is the patter is 50 cm. Order one or two extra rolls because there will be some wasted paper due to the pattern repeat. My roll started at 36 cm(cutting guide on the back) so the first thing I did was cut it off at 50 so the pattern on the first stri
Super cool look very dimensional
I wish I had a picture of this cause it really is beautiful as far as wallpaper goes. Love it!!!
We love the way our bathroom looks with these tiles. We just wanted a temporary change up so the self adhesive worked perfectly. I did cut the side bricks out so it looked more real to the quick eye.A couple of hints: Don't cut all of the tiles until you know how many you need to butt up to the corners. The glue is CRAZY sticky, be really careful not to get it on your nails. This is in my bathroom and I noticed that it shrank a little over night. The backing is HARD to peel off, I finally starte
says 58 square feet. NOT 58 feet . The pannels are only 15x14. It came out to 14.5 square feet.DO NOT BUY unless you love to stand in line at the ups store for returns.
I took the advice of one of the reviews that said to be sure that you cut them correctly and take your time to be sure that you use the beginning part to face you and the cut edge against the wall or corner. They do take some time to do, but very forgiving, because they are spongy and you can overcut around molding and then just tuck it in. They look awesome and I had no problem with them sticking but once I put them up, I took a towel and I made sure that I rubbed each section so that I knew that it was secured to the wall and be sure that you do clean your walls.
I ordered these to give my basement family room a little upgrade and they turned out great. I used liquid nails to apply them to the wall. The application was easy but cutting them is a hassle if you don't have the proper tools. I have gotten a lot of compliments on how it turned out. I plan on doing an accent wall in my bedroom. These are a nice and economical way to give your room a different look if you are on a budget!
Ive used this product before in a different application but this is by far the best yet! Easy to use, it does stick very well so just be sure of where you are placing it my inexpensive fireplace console was a perfect project, I added the mantle and the FAUX BRICK ! Love how it turned out! Thank you
I am at the tail-end of a long remodel and have zero patience at this point for anything that looks cheap, doesn't perform, and/or fights me during installation. I was somewhat skeptical because these are made from foam and are actually soft and squishy to the touch. But -- they actually do look real (or as real as you can get for not actually being real). I had 2 applications: around a kitchen island, and on a 3ish x 8 foot accent wall.I did the jigsaw method (cut out the small end squares) and
I recently added the 3D diamond wall panels to my boys room, and I have to say, they absolutely loved it! The transformation was incredible. Installing these panels was a breeze thanks to the gorilla glue construction adhesive. It held everything securely in place, ensuring a long-lasting installation. I was delighted to discover how easy it was to install the panels, saving me time and effort. To achieve a seamless finish, I used white caulk to fill any gaps between the panels, and the result
This was a week-long project that took several steps to complete. My project involved more than 160 panels. The panels themselves are very sturdy PVC, and the final product is an incredibly unique accent wall that complements my entire living room.Suggestions/info:- Per the manufacture' directions, take the panels out and let them "air out" for 24 hours before installing. When installing (potentially) hundreds of these, you want to make sure they are fully acclimated/adjusted to your environmen
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as "Tite Bond" or similar (available at Menards for instance). Your typical liqu
Hard to install but once in the all it looks amazing we painted ours and the paint held really good. We also use caulk on the seems to hide it and it came out really good.
Since I have used the peel and stick sheets before, I ordered 4 boxes of this product thinking that I would need way more than I did. Each box of 102 tiles equals about 12.75 square feet and that is VERY accurate. These tiles were SO easy to use and way more forgiving than the sheets of tile I had used before. Once the first row was applied using a level to ensure straight lines, we had the entire backsplash done in about 4 hours. I would suggest taking all the tiles from the box and re-stacking
Turned out very nice, if you want this to be an easy quick project then there are some things to consider.-This won't be a seamless look unless you're wanting to fill and paint, which I'd highly recommend. This means filling sanding and spraying-If you're going to the ceiling you'll want to caulk the meeting from the panel to the ceiling.-These cut very easy with scissors or snips.-Application with an instant grab adhesive will save you any hassle of the panel shifting or popping off the wall af
All I can say is WOW. Easy to use. Durable. Beautiful. I need more for other projects in my home.
Easy to install, looks stylish, great value for money. Installed on the back of a cabinet in my bathroom, and it' holding up great. Love it!
I am so in love with these! They were super easy and quick to install. Lined up really nice and gave my home such a cozy classy look. I would recommend to anyone! They are VERY sticky and will not come off without leaving a foamy mess behind so make sure u have them where you want them. (I know because i messed up at the beginning and had to pull one off lol )We have wallpaper behind ours so if we want to remove at some point it will be easy to pull everything off.
I am at the tail-end of a long remodel and have zero patience at this point for anything that looks cheap, doesn't perform, and/or fights me during installation. I was somewhat skeptical because these are made from foam and are actually soft and squishy to the touch. But -- they actually do look real (or as real as you can get for not actually being real). I had 2 applications: around a kitchen island, and on a 3ish x 8 foot accent wall.I did the jigsaw method (cut out the small end squares) and
Beautiful and strong!!!! It looks like real stone and it stick very well. Heat and water resistent. A bit hard to cut it. You will need a good cutter.
Incredibly light weight foam material with a textured feel. Pretty when installed and will add some insulation. Sticks well.
I am at the tail-end of a long remodel and have zero patience at this point for anything that looks cheap, doesn't perform, and/or fights me during installation. I was somewhat skeptical because these are made from foam and are actually soft and squishy to the touch. But -- they actually do look real (or as real as you can get for not actually being real). I had 2 applications: around a kitchen island, and on a 3ish x 8 foot accent wall.I did the jigsaw method (cut out the small end squares) and
Came out really cool! Still have to finish the bottom. The pieces are pretty difficult to cut so I guess just plan it out accordingly. There is also so many options on patterns you could design with this particular 3D panel. I might of gone for something way more complex if I planned it out on the floor first. Overall it made a boring wall very interesting. Used double sided table to hang them and cut them with extra long garden sheers. I did not cut them directly I cut into them congruently fol
Last year, we updated our kitchen and used a tile like this (but a different brand) as our backsplash. We loved the result and got so many compliments. When it came time to update our bathroom recently, we decided to do something similar and chose this product. (We selected the black version, although I have no idea what it' called that because there' no black in it.) This product is a quality product that looks very high-end and is easy to install. We've honestly recommended it to many peop
Last year, we updated our kitchen and used a tile like this (but a different brand) as our backsplash. We loved the result and got so many compliments. When it came time to update our bathroom recently, we decided to do something similar and chose this product. (We selected the black version, although I have no idea what it' called that because there' no black in it.) This product is a quality product that looks very high-end and is easy to install. We've honestly recommended it to many peop
The product is great and was easy to work , although the shipping was horrible very disappointed.
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as "Tite Bond" or similar (available at Menards for instance). Your typical liqu
No me agrado que la persona que lo entreg no sigui las instrucciones de entrega.
I took the advice of one of the reviews that said to be sure that you cut them correctly and take your time to be sure that you use the beginning part to face you and the cut edge against the wall or corner. They do take some time to do, but very forgiving, because they are spongy and you can overcut around molding and then just tuck it in. They look awesome and I had no problem with them sticking but once I put them up, I took a towel and I made sure that I rubbed each section so that I knew th
This product is soft, and I wouldn't expect it to harden. 3/8 was used to seal new clear glass shower panels. They were already in place but had some water leakage. I was able to work this between glass panels and tile surface. Both vertical and horizonal. Now shower is watertight no more floor leakage. This is a door less open shower.
Just extra use a gun glue
Ive used this product before in a different application but this is by far the best yet! Easy to use, it does stick very well so just be sure of where you are placing it my inexpensive fireplace console was a perfect project, I added the mantle and the FAUX BRICK ! Love how it turned out! Thank you
I took the advice of one of the reviews that said to be sure that you cut them correctly and take your time to be sure that you use the beginning part to face you and the cut edge against the wall or corner. They do take some time to do, but very forgiving, because they are spongy and you can overcut around molding and then just tuck it in. They look awesome and I had no problem with them sticking but once I put them up, I took a towel and I made sure that I rubbed each section so that I knew th
Easy to install, looks stylish, great value for money. Installed on the back of a cabinet in my bathroom, and it' holding up great. Love it!
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as Tite Bond or similar (available at Menards for instance). Your typical liqu
Easy installation so was super simple but looks very elegant
Looks good, nice adhesive.
This made our dull 1950' (sarcastic statement) apartment EXCITING again! We live in an old apartment, and not getting a deposit back lol We painted the wall blood orange and put up these PVC panels. I bought 2 boxes and used 1 box and a few of the second box. I did not go fully down to the bottom of the wall because we are buying a fire place that mounts to the wall. We pre measured that' the big gap you see at the bottom. I will update this post and show you all the fireplace we will be buyin
Turned out very nice, if you want this to be an easy quick project then there are some things to consider.-This won't be a seamless look unless you're wanting to fill and paint, which I'd highly recommend. This means filling sanding and spraying-If you're going to the ceiling you'll want to caulk the meeting from the panel to the ceiling.-These cut very easy with scissors or snips.-Application with an instant grab adhesive will save you any hassle of the panel shifting or popping off the wall af
Work great, looks great and was easy to apply. Great results for our schools faux fireplace.
Easy to use and apply onto wall with 3m removable tape/command strips.
So excited for this, the picture not hung yet. Trying to wait for Spring The picture is a Matisse who I love and a peony is my favorite so this is perfect.The company sent the picture fast with all the need things to hang it with.. screws, a leveler even a small package of M&M' . Would definitely order from them again. Highly recommend
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as "Tite Bond" or similar (available at Menards for instance). Your typical liqu
Before I purchased four boxes of the Wavy 3D Wall art I read as many reviews as possible and thought that this was something I could handle. As some reviews mentioned some do' and don'ts. Well.... it never occurred to me that the wall of my choice for the art was not entirely square. As I live in an older home. So my dilemma was how to keep the pattern going straight and level. Next was finding how to secure them to the painted wall which had texture on it. I measured out how many panels would
The end result was striking, but they take a bit to put up properly. Keep in mind that the paper absorbs moisture so the wall paper paste cased many of the tiles to expand and they no longer sat flush on the wall and pulled away in some areas. I had to reapply and then pin down the area that had warped from the past moisture and push pin to wall till it dried in place and re-blocked flat. Then I had to fill the holes and seams with plaster, dry and sand. Then I primed, and then I applied 2 coats
Easy installation it was super simple but looks very elegant
You really need to order the correct tape for this. You'll want 3M VHB 1/4" double sided tape. We used only a few strips for each panel and they hang great. Sure the paint will come off when you remove it, but it won't fall off either (which seems to be a common complaint)Got black panels for the gray walls and they look super nice. I didn't want a bunch of reflection which is why we went with black. The white ones will really make the color pop if you check out other reviews with pics.Overall,
easy to set up and work with. Finished product looks great
Easy to apply with the adhesive tape. Just added enough texture to a simple wall.
Lightweight and attractive. Makes a great accent wall!
Made my Bathroom BEAUTIFUL just like how I pictured it .
I'm a lady, wanna be handy woman, impatient but decided to try myself first and in case I get frustrated I would hire someone. I have never used gorilla glue cartridges or a gun for it. When bought the glue gun the guy in the store didn't explain correctly, but I saw a video on how to use it and it was fine.The panels are light, easy to apply the glue on, easy to clean when a little mess happened, easy to cut, I didn't use the tile blade because I was nervous I would cut myself, so I tried with
Came out really cool! Still have to finish the bottom. The pieces are pretty difficult to cut so I guess just plan it out accordingly. There is also so many options on patterns you could design with this particular 3D panel. I might of gone for something way more complex if I planned it out on the floor first. Overall it made a boring wall very interesting. Used double sided table to hang them and cut them with extra long garden sheers. I did not cut them directly I cut into them congruently fol
I bought these textured 3D wall panels after being inspired by an Instagram post and envisioned them enhancing my office space. Surprisingly, I ended up with 6 extra tiles and wasn't sure what to do with them. The photos in this review show how I creatively utilized these leftovers to fix an imperfection in a bedroom door. (I still havent had a chance to finish my new office space so Im not able to show photos of how that turned out yet.)During renovations, I accidentally damaged the door, cre
I love these tiles and how it amplifies the look of my dining room. I was worried about how to install them because there is little flat surface on the backs of each tile for glue. So I used double sided carpet tape and it worked great and was very easy to install. Tips: buy a flat, black paint to paint around each tile while you install. (Pictures provided for example) the tiles arent easy to cut. I used a razor blade and a strong pair of scissors.
I ordered these to give my basement family room a little upgrade and they turned out great. I used liquid nails to apply them to the wall. The application was easy but cutting them is a hassle if you don't have the proper tools. I have gotten a lot of compliments on how it turned out. I plan on doing an accent wall in my bedroom. These are a nice and economical way to give your room a different look if you are on a budget!
Excelente material y muy fino
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as "Tite Bond" or similar (available at Menards for instance). Your typical liqu
Minimal effort for maximum results. We wanted to put together a mini playroom for our daughter that was also aesthetic. Our walls looked pretty plain and I wanted a nice contrast / statement wall, but didnt want to paint it. I found these and they couldnt have been more perfect. I used one and a half packs for the entire mini playroom, and did the job in about an hour. I would first line up each piece, hold the bottom half while peeling the back off the top. Then I would push the top to stick,
The end result was striking, but they take a bit to put up properly. Keep in mind that the paper absorbs moisture so the wall paper paste cased many of the tiles to expand and they no longer sat flush on the wall and pulled away in some areas. I had to reapply and then pin down the area that had warped from the past moisture and push pin to wall till it dried in place and re-blocked flat. Then I had to fill the holes and seams with plaster, dry and sand. Then I primed, and then I applied 2 coats
So . . . short story time. I had to have a plumber cut into my wall to replace the outdoor hose faucet. I did not have any of the red paint left because I painted this powder room YEARS ago. SO, it was finally the time to do that accent wall I'd wanted. I looked at a ton of peel and stick tiles and settled on these foam brick tiles. They are very easy to use and as long as you TAKE YOUR TIME lining them up before you stick them, you will have no issues and your project will be amazing.Things I l
Yay! I'm the first review! It was hard finding information about this product before I bought it so I wanted to come back here and share my thoughts on the Moon Surface 3D wall panels to help other people who might be interested in purchasing. Some of the product photos look like they were Photoshoped so I wanted to share some real feedback.I renovate and flip mid century modern houses and I wanted to add texture and depth in a way that would compliment the home while adding a unique design feat
I like that the panels were easy to position and they did the job well.
The end result was striking, but they take a bit to put up properly. Keep in mind that the paper absorbs moisture so the wall paper paste cased many of the tiles to expand and they no longer sat flush on the wall and pulled away in some areas. I had to reapply and then pin down the area that had warped from the past moisture and push pin to wall till it dried in place and re-blocked flat. Then I had to fill the holes and seams with plaster, dry and sand. Then I primed, and then I applied 2 coats
Very easy to use.Cut with scissors or razor knifeThe glue is very sticky. I did add some additional just to be safe.Looks great and is paintable
These tiles are large. Cut to size. Pattern matched well and if you take your time you can hide seems. I stapled mine up but the adhesive is no joke. Easy to cut and only took me about 40 min to do a 11x9 wall.
These 3D wall panels are so cool I used them to design a whole wall from ceiling to floor as a statement wall. They're very durable a really nice size for coverage and can be painted.
Took awhile to arrive but these are great! we have textured walls so we used a staple gun to mount them instead of the adhesive backing. i used scissors and a razor blade to trim and cut and overall im loving how this is coming together! this was a trial run for a larger space we wanted more of an industrial look in and these are working out better than i expected. Loved these so much we bought more for the bathroom and my husband' office. using a staple gun makes installing these a breeze and
I love it. It is so easy and look so beautiful. I am so happy with it looks.
This product was perfect for my project. You have to take your time when working with these, but the result is beautiful. They were very easy to cut, I caulked between the joints then primed and painted them. Definitely worth the effort for the price.
I love this product! Lightweight. Easy to use. It shipped quickly. I loved it so much I kept ordering more. What started out was a fireplace hearth expanded into being a full wall covering, because I loved it so much.It worked perfect for this faux fireplace. It stuck to the wall basically with tape. I did add grouting between the stones to make it look more authentic and to make it looks seamless.Great value for the money.
awesome design and detail
Package arrived quickly with all panels exactly as ordered. Upon first glance, these panels are obviously extremely fake looking, with a shiny, plastic-like appearance. You do get what you pay for, and these panels were very affordable compared to having a brick wall built. But, with a little extra time and a few easy modifications, they look 100% authentic-even up close. I did not have any issues with removal of the backing (did so very slowly and in smaller segments on each panel) or the panel
Well it took 2 cases to make my vision emerging to reality. And it worked perfect for my entertainment center with some back lights on the TV the living room. This contemporary design adds a modern theater look too the setup.
Impressed with TORURAL Faux Brick Wall Tiles! Used two colors for texture, and the result is fantastic. Easy to work with, lightweight, and they create a realistic, eye-catching finish!Make sure you read instructions and have all tools when you start! A level was very helpful and keep in mind the dry time on your materials! I definitely needed a brick haze remover at the end!
These panels double back tape on and they are funky fresh cool. They immediatly change the mood of a room and modernize it. They can be painted as well but no need to in my opinion. This is exactly as shown and described and works as promised. It meets our needs and expectations and is well made of durable materials.
Really sticky doesnt fall off and last Ive had mine for atleast a year!
LOVE how these tiles worked out. I had no expectations as I figured they were too good to be true given they were stick-on and lightweight. Fantastic pop of texture and artsy aesthetic.
I have not placed these on wall yet. But, held a few up and I love the look. Price was right and they are going to look great. Delivery was fast and quality is good.
After it went south north south north north and then arrived at my house with a big hole on the box - as it typically happens with every shipment through the POST office USPS - whats this Oops we dont like it - I hit it! Better than I thought. Sticks and doesnt come off, easy to install, and realistic. Buy it
Easy to put on walls. Looks great
This is one of the best product experiences Ive had in a long time from amazon, and that says a lot! I used one full package and applied using the interlocking method; it took about 10 hours total over two days (one person doing all the cutting, measuring, applying, trimming, etc, with kids around). Ive included some before, during and after photos. We also added a shelf and cast iron brackets, shown in the photos. We absolutely love the outcome, and it changed the whole room for less than $20
It was very easy to do. The material is very hard to cut so have some large sharp scissors.
In love with this wallpaper! We are turning a closet into a mudroom and it turned out nice! A little time consuming and difficult to line up but with 2 people we managed to get it done! Love the look
Stunning and rental friendly!!I decorated this room to list on Airbnb and these took it next level! Since we do not own the house, I used 3m command strips and glue dots around the edges to attach to the walls so they can come off when we move without damage. Even if I owned it I would go the same route so I didnt have to make major repairs later on.The only negative is when you have outlets or light switches on the wall. When you cut out the panel to accommodate them it reveals the hollow 3d n
These look so real and really stick to the wall!
Used this to make an accent wall. Easy to work with, product arrived in perfect condition. Very happy with the finished product!
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as Tite Bond or similar (available at Menards for instance). Your typical liqu
They're extremely sticky which is good, but it' a rascal to scrape off if you don't lay it right. Peeling the paper off a little at a time, stick it to the most critical corner first, & then peel & stick the rest with precision, typically getting the top or side right where it meets the last piece & then peel a little & stick a little until it' all on there.We used a putty knife to scrape half of one off & re-aligned it, and it still stayed, though the sticky was compromised. Cool it still wor
Used these for a kitchen wall to brighten up the room. VERY sticky, but easy to install. Had to waste a few only because of the sticky-ness (to the fingers). Great cover. Very neat and clean. So far, easy to clean too. I do notice in a couple of the areas a separation at the seams, and unable to lift up the area and reposition because they are very stuck
I am at the tail-end of a long remodel and have zero patience at this point for anything that looks cheap, doesn't perform, and/or fights me during installation. I was somewhat skeptical because these are made from foam and are actually soft and squishy to the touch. But -- they actually do look real (or as real as you can get for not actually being real). I had 2 applications: around a kitchen island, and on a 3ish x 8 foot accent wall.I did the jigsaw method (cut out the small end squares) and
I am at the tail-end of a long remodel and have zero patience at this point for anything that looks cheap, doesn't perform, and/or fights me during installation. I was somewhat skeptical because these are made from foam and are actually soft and squishy to the touch. But -- they actually do look real (or as real as you can get for not actually being real). I had 2 applications: around a kitchen island, and on a 3ish x 8 foot accent wall.I did the jigsaw method (cut out the small end squares) and
Been thinking about doing something different with the wall for a while. Recently, a friend suggested adding wood wall panels. After seeing some photos on the internet, just couldn't wait to do it to my living room wall. I have ordered this product after quite a bit of research. Glad that it did not disappoint me. My wall looks amazing now. It was easy to install with the provided adhesive and installation instructions. I loved the packaging. It was packaged with so much care to make sure no dam
These peel and stick tiles are great! They look really nice, they are very light so they don't add a lot of weight, and they stick so good! I love the 3D look that actually gives it they look of stones or brick. You can literally use these just about anywhere! They could be used for backsplash over your sink or by your stove. You could use them around your fireplace or really anywhere that you are looking for the look of stone or brick without having to install stone or brick! They were very eas
These wall panels catch light depending on which way they are turned. Their faces change throughout the day as the sun changes position. The covering material is strong and washable with a damp cloth. Very nice looking. When cutting them, you may want to use grey acrylic paint on the foam core to get the edges to match. A modest sized entertainment center wall took 10 packs of 20 (including practice cuts), which is not cheap.
Glue on backing is extremely durable!
I liked the idea but you need to be very good a cutting measuring and have extra glue as well as a good surface to work with. For folks that aren't advanced at home projects I would say no.
